[ Closed ] XP11.35 JD330 v.3.2 r4 (Page 4 of 6)

work well

Getting this message "VA Plug in Error". What am I suppose to do? Log Attached.

Hello, sorry if my problem has already been mentioned but I do not know where to look to see if there is already a solution.

I bought the 330 this morning and I just tested the ground procedures at LFBO. Tonight I wanted to fly KJFK/KLAX but when I entered my information on the FMC INIT page, I noticed that KJFK's GPS position was wrong with a latitude value of -73 ° instead of 73 °.

I saw that this problem existed on the 320 and that it seemed to be fixed but I did not find an identical mention for the 330.

Thanks in advance for your help, sorry for my english and again sorry if the problem had already been reported.

PS : I don't see any answer to know if WX Radar works with xEnviro?

How do you enter your information in init page?

In Init page write LFBO/KLAX and press right button on from to and you get direction. Request for flight plan not working on overseas destination, so you get only departure and arrival airport in your flight plan. You can use SimBrief to make flight plan, save to your flight plans and the in init page write LFBOKLAX and pres left button near your CORTE, and you get flight plan. You need aproksimatly 61 tons of fuel to this destination.

Dont forget to fulfill  the PERF page before start flight and use copilot for help.

In the and FIRST you MUST READ how to fly with A330. First you can use this link http://jardesign.org/forum/viewtopic.php?id=3059

At least this is not arcade game but simulation and must be real they came to be.

Regards

Thank you for your answer but it does not answer my problem.

I said that the GPS position of the departure airport was lost after I got KJFK/KLAX on the INIT page. When I confirm this, the GPS position where we click on ALIGN IRS on the INIT page is wrong and so I have a DISCONTINUITY between the departure airport and the 1st WAYPOINT of the route.

I explained my problem to a friend who owns the A330 JAR and he too has encountered this problem.

I found the little problem,
In the X-plane log file I found the JAD330 display the
FMGS: 1089 : JARDesign plugin error: Unsupported protocol
FMGS: 1089 : CurlDownloadFile Error

I used a web browser to visit https://tgftp.nws.noaa.gov/data/observa … s/KCPR.TXT  which displays the following data:
2019/09/06 14:53
KCPR 061553Z 12006KT 10SM CLR 24/09 A3024 RMK AO2 SLP165 T02440094
But I opened the downloaded .txt file and found that the content is blank~ 

Attached with the relevant files for your reference.
Thank you.

Hi, works well in VR, just a couple of things.
1, gear up down not working in VR.
2, Flaps not working in VR
3, cant arm speed brakes in VR.

Just wonder if these can be fixed?

Would be nice if you can?
thanks
carl

It does not work if you have x enviro.

This dome light works?Looks like it does not work. Anybody knows something about that? Of course HDR is set and level of details is Maximum (HDR+SSAO)?

OK works fine... Did not turn on this CTL switch...

1/ Guys do you have a bug when you set up FMC and flying and later you had to change the approach and runway due to ATC? Each time I change that it turns out that memorized ILS (RAD/NAV key) in this case is from the initial input (let's say RWY 25L while ATC gave me 25R and different STAR than initial input)

2/ Sometimes ATC gives me an instruction that on WAYPOINT let's say XYZ I had to be on 9000ft, while in flight plan it's on 16000ft. Well it's quite obvious ATC want to point me earlier to approach. Normally it needed to put into FMC /FL090 and push it to the point so the FMC will recalculate the rest, but it's impossible. Any clue?

JAR can you take a look at it?

Flaps up 0 from flaps 4 when after landing, the speed brake will not show animation by replay mode.