[ Closed ] JD320 Airliner ver 3.6 WIN/MAC 64 bit (X-Plane 11.50/11.41) (Page 2 of 6)

AT THE TAKE OFF it does not come out the VR in the pfd

JD-CPL-320

Good day,

Here is a list of errors for the JD A320 v3.6RC1

1. I use the Thrustmaster T.16000M, and so far I have been able to adjust the spoilers with the Throttle (2). This is no longer possible with the V3.6RC1. I can only change the position of the spoiler armed to disarmed. I can adjust the spoilers with the mouse. Please correction.

2. - if you use BSS soundpacks, please note what "Modules / Custom Module /" now is the same as "Custom Avionics /" folder
When I copy the files of the Optional FA announcements (Custom Avionics) into the directory "Modules / Custom Module /", I don't get a BSS sound. But if I copy the files from the Custom Avionics directory to plugins / sound2, then I also get the additional announcements. There is an error here.

3. The announcements of the checklists are missing, please add. I don't want to use the co-pilot.

greetings
Horst

As always Jar Design A320 Great aircraft to fly, i have up-dated to version JD320-V3.6RC1  but i do have a slight problem when you taxi and turn in the air the Hdg Knob turns and makes clicking noise? is this a bug or can it be turned off

Many Thanks

Mike

Hi, when the aircraft loads, there's a nice and clean looking MCDU/FMC pop-out in a lighter grey colour (see attached image). If I've closed this MCDU, how do I bring it back up ? Clicking the cockpit MCDU(s) only pops up the darker and less readable ones.

It's a pity we cannot set the FCDU altitude with the xplane commands AUTOPILOT ALTITUDE UP/DOWN

This issue happened to me today too, while I was approaching around 500 ft i disengaged the autpilot and started to approach but suddenly the pitch started to change randomly it went to positive 14 and straight away to negative Hope you will take a look at it just wanted to report it thanks! have a good day

Hi sir, thanks for the update. I am currently running a320 latest version on xplane 11.50 RC3, and I found some issue down below:
1. When I was flying older a320 version 3.3 r3, the engine indicator in the central panel is spot on (if the small indicator set to 40%, then the n1 will not exceed that value. In the most recent version, I found that has changed and not linear anymore (when the indicator is 40% it will rock to 50-60% n1). And during takeoff I usually set to TO/GA. In the past,  TO/GA will be between 90-100% depending on my PERF setting. In the most recent version, my TO/GA value will not exceed 82-85%. Although I could still takeoff as usual, I just wondering if it is a bug or I think too much.
2. I found that the ATIS receiver will cause a CTD in the latest x-plane 11.50 RC3, and with the old model 3.3r3 it was fine. Please investigate this problem since getting updated weather from the sim is quite useful and important in takeoff and approach phase.
Otherwise, great update overall, especially the ground handling and load config!

XP 11.50 is now final and released.
Jardesign A320 can now made final for the use with XP 11.50, after the repair of some reported issues of course.

Hi, on older versions there was an option on the MCDU menu to display a shortcuts toolbar which gave quick access to functions such as towing and fuel. I can no longer see that. Has it been removed?

Thanks a lot for this sir they work flawlessly now, For the FMC is there a possibility to add the feature of PLACE DISTANCE POINT? This would be very useful if it is actually added to the JARDESIGN A320 thanks a lot great update!

I had to reinstall my airplane because of the update. But now every time I try to load in the aircraft a second time(because the first time I opened it I wasn't able to but my serial key in)  I´m getting message which says: "Mac.xpl cannot get searched for virus because it isn't verified. if I press on open it pops on another time if I press on open again I instantly get kicked out of xplane. I´m on Mac btw so I really need help because I don't know what to do.