[ Closed ] X-Life ver 1.0 (rc1, r1, ++) (Page 6 of 28)

dadez77 wrote:

Hi Eugeny,

just complete a test flight from LIRF to LFMN, all works like a charm execptfor the departure SID, the delivery not assign any SID.

Do you remember our flight with skype desktop sharing? In that flight i have had the same problem, deliver give the clereance but without SID.

For the rest all works fine

thanks for all

Yes, I remember, BUT seems like this is Navdata issue.. as example -

+We select LIRF RW25 for takeof.
+We find a SID at LIRF.txt proc file - EKLO5R

SID,EKLO5R,25,5
CA,0,248,2,410,0,0,0,0,0,0
DF,RF726,41.79547222,12.21821667,0, ,0.0,0.0,0,0,0,1,210,0,0,1
DF,RF701,41.83262778,12.13183611,2, ,0.0,0.0,2,2800,0,1,240,0,0,1
DF,RF703,41.71315833,12.14123333,0, ,0.0,0.0,2,6000,0,0,0,0,0,0
TF,EKLOS,41.57250000,12.30027778,0, ,0.0,0.0,0,0.00,2,8000,0,0,0,0,0,0

+We take Last SID point and it is EKLOS
+We try to build route to arrival using airways, open ats.txt file and.. and.. and..

THERE is No EKLOS point in the ats.txt That mean what EKLOS point not a part of ANY airroute and it can not be used for routebuilding. OOOOpssss! I am stuck.. ATC too, cause it use my brain logic

Good day.
Fly on the route ULLI-EETN on the A330. The entire flight without any problems, the plugin worked correctly, except for two moments.
1. The instruction ATC: AFL1342, Descend to 2200 feet, QNH 1024, transition level FL 50. But to NOAA_Weather METAR, METAR in the A330 and the summary ATIS QNH1025.
2. Parking lot plug-C_8 determined, but Parking for this type of aircraft "A". The screenshot is attached.
And another question. When you select the position control, the frequency to be transferred on the radio panel of the aircraft, and if the frequency of the wind on radiopanel in the plugin it is not broadcast. This is a mistake? Or will this be implemented in future versions of the plugin?

Добрый день.
Полет по маршруту ULLI-EETN  на А330. Весь полет без проблем, плагин отработал правильно, за исключением двух моментов.
1. Указание ATC: AFL1342, Descend to 2200 feet, QNH 1024, transition level FL 50. Но в METAR NOAA Weather, METAR в А330 и в сводке ATIS QNH1025.
2. Стоянку плагин определил C_8, но эта стоянка для типа самолетов "А". Скрин прилагаю.
И еще вопрос. При выборе позиции контроля, частота переноситься на радио панель самолета, а если частоту накручиваешь на радиопанели то в плагин она не транслируется. Это ошибка? Или это будет реализовано в последующих версиях плагина?

Good day.

Но скорее всего АТС не смогла найти подходящую и свободную стоянку для этой категории самолета (плагин анализирует размах крыльев, сопоставляет с категориями стоянок и пытается найти подходящую) и выдало стоянку с индексом 0 (самая первая в списке стоянка). Я подумаю, наверное правильнее - подставлять не 0-ю стоянку а с максимальной категорией по размаху крыльев. Попробуем в следующей бете.

Thanks!

CTDs getting quite frequent now.
Holding short at KBOS RW15L

MacBook Pro Retina, 15’’, late 2013, OSX 10.11.4, 16GB RAM, NVIDIA GT 750M 2GB
Saitek X52,  Radio, Switch and Multi Panel, TM Cougar, XP 10.45, JAR A320neo 2.6.1, XL 1.1b1

laohu314 wrote:

CTDs getting quite frequent now.
Holding short at KBOS RW15L

MacBook Pro Retina, 15’’, late 2013, OSX 10.11.4, 16GB RAM, NVIDIA GT 750M 2GB
Saitek X52,  Radio, Switch and Multi Panel, TM Cougar, XP 10.45, JAR A320neo 2.6.1, XL 1.1b1

May be a real reason - KBOS. What .dat and .txt you use?

Hi guys,

I'm having two issues and they only appeared with the last few updates. I use XLD to create a flight plan from 2 xlife airports. XLD creates the flight plan but repeats way points throughout the plan making what should be a 1600NM trip into 20000NM (albeit with correct waypoints etc, just repeated over and over).

I can't figure out what's causing it. The only thing I've done recently is update the AIRAC to 1604. The FMC in both the A320 and A330 show this correctly and I have no issues creating, saving then importing my own flight plans from Rfinder for example. The issue seems to lie with XLife and the way it's creating the flightplans. 

I can also save flight plans from Rfinder in the Xlife flightplans folder and import them.

Another issue that came to light today is that the XLD flight planner will now not export data to the FMC?
Any ideas?

Thanks, Ben.

How do you guys create the ICAO.txt files for use with x-life, I don't mean what editor BUT where do you get the info from